• 32-inch LCD TV
• 5000:1 Dynamic Contrast Ratio
• AV Mode
• 5ms response time
• Invisible Speakers
• Clear Voice
• HDMI 1.3 – Deep Color
• SIMPLINK System
• 1366 x 768 pixels resolution
• 200 watts PMPO output
• PC Input and 2 HDMI Inputs

Dimensions (Width x Height x Depth)

• with stand -801.7 x 604.2 x 227.3 mm /31.5 x 23.8 x 8.9 inches
• without stand -801.7 x 544.1 x 79 mm /31.5 x 21.4 x 3.1 inches

Weight

• with stand -13.35 kg / 29.4 lbs
• without stand -11.85 kg / 26.1 lbs

AC100-240V~ 50/60Hz Power requirement

PAL/SECAM B/G/D/K, PAL I/II, NTSC-M Television System

VHF: NZ1~E21, UHF: E21 ~ E69, CATV: S1 ~ S20, HYPER: S21 ~ S47 Program Coverage

75 Ω External Antenna Impedance

Environment condition

• Operating Temperature -0 ~ 40°C / 32 ~ 104°F
• Operating Humidity Less than 80%
• Storage Temperature -20 ~ 60°C / -4 ~ 140°F
• Storage Humidity Less than 85%

• Carefully place the TV screen side down on a cushioned surface to protect the screen from damage
• Assemble the parts of the Stand Body with the Cover Base of the TV
• Insert the STAND BODY into a COVER BASE until clicking sound
• Fix the 4 bolts securely using the holes in the back of the TV
• Use the eye-bolts or TV brackets/bolts to fix the product to the wallInsert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes
• Secure the wall brackets with bolts to the wall
• Ensure that both brackets are even
• Use a strong cord to secure the TV
• Secure the cord in such a way that it becomes taught when the TV is in position
• Connect the cables as necessary
• Open the CABLE MANAGEMENT CLIP and manage the cables
• Fit the CABLE MANAGEMENT CLIP
• After connecting the power cord to the AC input terminal, fix the power cord at the rear side Hole of the TV by using the bracket for fixing the power cord
• To prevent damage do not connect to the mains outlet until all connections are made between the devices
• For optimum picture quality, adjust antenna direction
• An antenna cable and converter are not supplied
• In poor signal areas, to achieve better picture quality it may be necessary to install a signal amplifier to the antenna
• If signal needs to be split for two TVs,use an antenna signal splitter for connection

• Early malfunctions can be prevented. Careful and regular cleaning can prolong the life of your new TV
• Be sure to swith the power off and unplug the power cord before you begin any cleaning.

Cleaning the Screen

• A good way to keep the dust off your screen for a while is to wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and then use it to wipe the screen
• Ensure there is no excess water on the screen. Allow any water or dampness to evaporate before switching on

Cleaning the Cabinet

• To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth
• Do not to use a wet cloth

• To prevent TV from falling over, the TV should be securely attached to the floor/wall per installation instructions. Tipping, shaking, or rocking the machine may cause injury
• When moving the TV undo the cords first
• Use a platform or cabinet string and large enough to support the size and weight of the TV
• To use the TV safely make sure that the height of the bracket on the wall and on the TV is the same
• Do not use the CABLE MANAGEMENT CLIPto lift the TV - If the TV is dropped, you may be injured or the TV may be damaged
• Ensure that you connect the earth wire to prevent possible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker
• Do not try to earth the TV by connecting it to telephone wires, lightening rods or gas pipes
• To avoid damaging any equipment, never plug in any power cords until you have finished connecting all equipment
• This section on EXTERNAL EQUIPMENT SETUP mainly uses diagrams for the PLASMA TV models

TURNING ON THE TV

• When your TV is turned on, you will be able to use its features
• Firstly, connect the power cord correctly
• At this stage, the TV switches to standby mode

INITIALIZING GUIDE

• It will automatically disappear after approx. 40 seconds unless a button is pressed
• “In -Store” mode is only for shop display and not for general customer use
• "Home” mode is the optimal setting for home environments, and is the TV's default mode
• "In-Store" mode is the optimal setting for store environments. If a user modifies image quality data, “In- Store” mode initializes the product to the image quality set by us after a certain period of time
• The mode (Home, In- Store) can be changed by executing Factory Reset in the Option menu

QUICK MENU

• Your TV's OSD (On Screen Display) may differ slightly from that shown in this manual
• Q.Menu (Quick Menu) is a menu of features which users might use frequently
• Aspect Ratio: Selects your desired picture format. For Zoom Setting, select 14:9, Zoom1 and Zoom2 in Ratio Menu. After completing Zoom Setting, the display goes back to Q.Menu
• Power Saving (only Plasma TV Models): Adjusts screen brightness to reduce the power consumption of the set
• Backlight (only LCD TV Models):Adjusts screen brightness. It returns to the default settings brightness by changing mode source.
• Picture Mode : Selects your desired Picture Mode
• Sound Mode : It is a feature to automatically set the sound combination which it deems the best for the images being watched. Selects your desired Sound Mode
• Multi Audio : Selects the sound output
• Programme Edit : Adjusts the stored programmes by delete, copy, move or skip
• Sleep Timer : Selects the sleep timer

AUTO PROGRAMME TUNING

• Stations can be tuned using automatic or manual modes
• All stations which can be received are stored by this method. It is recommended that you use Auto tuning during installation of this TV

MANUAL PROGRAMME TUNING

• Manual programme lets you manually tune and arrange the stations in whatever order you desire

BOOSTER

• In some models, Booster is an optional function. Only a set with Booster can perform this function
• If reception is poor select Booster to On
• When the signal is strong, select “OFF”